产品banner
Products

low porosity clay bricks for glass kilns

low porosity clay bricks are mainly used in the regenerators of glass kilns. They can also be used in blast furnaces and hot blast furnaces in the steel industry; cement kilns in the building materials industry; chemical kilns in the chemical industry as kiln linings

Related Products
  • Clay refractory bricks
    Fireclay bricks for hot-blast stoves

    Fireclay bricks are classified as weak acid refractories. Due to the large fluctuation range of chemical composition, different production methods, and differences in firing temperature, the properties of clay bricks change greatly.We can produce all kinds of Fireclay bricks according to customers' requirements

  • clay bricks
    Physical and chemical indicators of low creep rate clay bricks

    Fireclay bricksis suitable for supporting hot blast stoves of large, medium and small blast furnaces

  • clay insulation bricks
    Physical and chemical indicators of clay insulating refractory bricks

    The Al2O3 content of clay heat Clay insulating refractory bricks is generally more than 40%, and the Fe2O3 content is less than 2.0-2.5%. The clinker in the ingredients is 65-85%, and the combined clay is 35-15%. The crushed bonded clay and the finely ground clinker are mixed and milled, and then mixed with the granular clinker to make semi-dry mud, high pressure molding, and sintering at about 1400 ℃, with good performance.

  • fire clay bricks
    Fire clay bricks for coke oven

    The refractoriness of clay bricks is comparable to that of silica bricks, up to 1690~1730℃, but the softening temperature under load is more than 200℃ lower than that of silica bricks. Because in addition to the high refractory mullite crystal, the clay brick also contains nearly half of the low melting point amorphous glass phase.

  • Magnesium alumina spinel brick
    Magnesium alumina spinel brick for lime kiln

    Magnesia alumina bricks use periclase as the main crystal phase and magnesia-alumina spinel as the matrix. They are better in thermal shock resistance than magnesia bricks. In order to improve the thermal shock resistance of magnesia bricks, alumina or alumina is introduced into the ingredients. Bauxite clinker fine powder to form a magnesia-alumina sharp stone matrix, thereby making magnesia-alumina bricks

  • tap hole mix for blast furnace
    Anhydrous tap hole mix for blast furnace

    Anhydrous tap hole mix for blast furnace tap hole

  • PRECAST SHAPES
    Pre Cast Refractory Shapes for High Temp Furnaces

    The refractory pre -production is the category of irregular refractory materials, also known as the prefabricated block of the pouring materials, and the irregular refractory prefabricated block.

  • Ramming mix
    Ramming material for blast furnace

    The refractory ramming material is prepared from a high proportion of granular and powdery materials and a very low proportion of binders and other components, even all of which are composed of granules and powders, and are subject to strong ramming. Bulk materials for construction.

  • Clay refractory bricks
    Fireclay bricks for hot-blast stoves

    Fireclay bricks are classified as weak acid refractories. Due to the large fluctuation range of chemical composition, different production methods, and differences in firing temperature, the properties of clay bricks change greatly.We can produce all kinds of Fireclay bricks according to customers' requirements

  • clay bricks
    Physical and chemical indicators of low creep rate clay bricks

    Fireclay bricksis suitable for supporting hot blast stoves of large, medium and small blast furnaces

  • clay insulation bricks
    Physical and chemical indicators of clay insulating refractory bricks

    The Al2O3 content of clay heat Clay insulating refractory bricks is generally more than 40%, and the Fe2O3 content is less than 2.0-2.5%. The clinker in the ingredients is 65-85%, and the combined clay is 35-15%. The crushed bonded clay and the finely ground clinker are mixed and milled, and then mixed with the granular clinker to make semi-dry mud, high pressure molding, and sintering at about 1400 ℃, with good performance.

  • fire clay bricks
    Fire clay bricks for coke oven

    The refractoriness of clay bricks is comparable to that of silica bricks, up to 1690~1730℃, but the softening temperature under load is more than 200℃ lower than that of silica bricks. Because in addition to the high refractory mullite crystal, the clay brick also contains nearly half of the low melting point amorphous glass phase.

  • Magnesium alumina spinel brick
    Magnesium alumina spinel brick for lime kiln

    Magnesia alumina bricks use periclase as the main crystal phase and magnesia-alumina spinel as the matrix. They are better in thermal shock resistance than magnesia bricks. In order to improve the thermal shock resistance of magnesia bricks, alumina or alumina is introduced into the ingredients. Bauxite clinker fine powder to form a magnesia-alumina sharp stone matrix, thereby making magnesia-alumina bricks

  • tap hole mix for blast furnace
    Anhydrous tap hole mix for blast furnace

    Anhydrous tap hole mix for blast furnace tap hole

  • PRECAST SHAPES
    Pre Cast Refractory Shapes for High Temp Furnaces

    The refractory pre -production is the category of irregular refractory materials, also known as the prefabricated block of the pouring materials, and the irregular refractory prefabricated block.

  • Ramming mix
    Ramming material for blast furnace

    The refractory ramming material is prepared from a high proportion of granular and powdery materials and a very low proportion of binders and other components, even all of which are composed of granules and powders, and are subject to strong ramming. Bulk materials for construction.

  • Clay refractory bricks
    Fireclay bricks for hot-blast stoves

    Fireclay bricks are classified as weak acid refractories. Due to the large fluctuation range of chemical composition, different production methods, and differences in firing temperature, the properties of clay bricks change greatly.We can produce all kinds of Fireclay bricks according to customers' requirements

  • clay bricks
    Physical and chemical indicators of low creep rate clay bricks

    Fireclay bricksis suitable for supporting hot blast stoves of large, medium and small blast furnaces

  • clay insulation bricks
    Physical and chemical indicators of clay insulating refractory bricks

    The Al2O3 content of clay heat Clay insulating refractory bricks is generally more than 40%, and the Fe2O3 content is less than 2.0-2.5%. The clinker in the ingredients is 65-85%, and the combined clay is 35-15%. The crushed bonded clay and the finely ground clinker are mixed and milled, and then mixed with the granular clinker to make semi-dry mud, high pressure molding, and sintering at about 1400 ℃, with good performance.

  • fire clay bricks
    Fire clay bricks for coke oven

    The refractoriness of clay bricks is comparable to that of silica bricks, up to 1690~1730℃, but the softening temperature under load is more than 200℃ lower than that of silica bricks. Because in addition to the high refractory mullite crystal, the clay brick also contains nearly half of the low melting point amorphous glass phase.

  • Magnesium alumina spinel brick
    Magnesium alumina spinel brick for lime kiln

    Magnesia alumina bricks use periclase as the main crystal phase and magnesia-alumina spinel as the matrix. They are better in thermal shock resistance than magnesia bricks. In order to improve the thermal shock resistance of magnesia bricks, alumina or alumina is introduced into the ingredients. Bauxite clinker fine powder to form a magnesia-alumina sharp stone matrix, thereby making magnesia-alumina bricks

  • tap hole mix for blast furnace
    Anhydrous tap hole mix for blast furnace

    Anhydrous tap hole mix for blast furnace tap hole

  • PRECAST SHAPES
    Pre Cast Refractory Shapes for High Temp Furnaces

    The refractory pre -production is the category of irregular refractory materials, also known as the prefabricated block of the pouring materials, and the irregular refractory prefabricated block.

  • Ramming mix
    Ramming material for blast furnace

    The refractory ramming material is prepared from a high proportion of granular and powdery materials and a very low proportion of binders and other components, even all of which are composed of granules and powders, and are subject to strong ramming. Bulk materials for construction.

Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
Top
Leave A Message
Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

Home

Products

skype

whatsapp